Home » Component data » RF mixers (Frequency mixers) » this page

ADE-1H+ RF Mixer Data

Data for the Mini-Circuits ADE-1H+ +17dBm LO passive RF mixer (or frequency mixer) including key the mixer type, whether it is balanced double balanced, etc, electrical parameters, pinout, package type and many other key datasheet details.

The ADE-1H+ is a passive mixer coving 50MHz to 500MHz and it is effectively the high LO power version of the ADE-1+ as the ADE-1H+ has a +17dBm local oscillator input level.

Rge higher LO input level mens that it can handle high signal levels as it has a much higher IP3 level specification.

Key details and performance parameters for the ADE-1H+ RF mixer.

ADE-1H+ RF mixer datasheet parameters & data
Parameters	Details
RF mixer type	Passive double balanced mixer
Package type	CD636
Active / passive	Passive
Supply voltage	N/A
RF input frequency range	0.5 to 500 MHz
IF Frequency range	DC - 500MHz
Conversion gain / loss	-5.3dB typical
LO to RF isolation	52dB
LO to IF isolation	42dB
Third order intercept, IP3	23dBm typical mid band
RF input power	200mW max
LO input power	+17dBm optimum input level
Maximum LO input VSWR	2.2:1
Maximum RF input VSWR	1.6:1
Primary manufacturer	Mini Circuits

Outline & Pinout:

Explanation of RF mixer parameters

Parameter	Explanation
Input Frequency range	Most RF mixer have a frequency range over which they can operate. As a result of the components used, this might include both upper and lower limits.
IF Frequency range	This is a specification used on some RF mixers and it defines the frequency range for the IF output.
Conversion gain / loss	Active miers often offer a level of gain between the RF input and the IF output. Passive mixers will introduce a loss. The conversion gain, measured in dB is a measure of this.
Noise figure	This is an important factor for low noise systems and it is a measure of te noise introduced. It is expressed in terms of dB.
LO to RF isolation	It is important that the normally high level local oscillator signal is isolated from the RF input, otherwise spurious signals might be generated.. This parameter gives a measure of the isolation or reduction in the LO signal from the LO input to the RF input and it is expressed in dB.
LO to IF isolation	This is the isolation, i.e. reduction in the level of the LO signal between the local oscillator input to the IF output expressed in dB.
RF to IF isolation

Parameter	Explanation
Output third order intercept, OIP3	The Third Order Intercept Point (IP3) for an RF mixer is a theoretical power level at the input (IIP3) or output (OIP3) where the power of the desired signal and the third-order intermodulation distortion (IMD3) products become equal.
Output 1dB compression point	The 1dB compression point of an RF mixer is the input power level at which the desired output signal power drops by 1 dB below the level expected from the ideal linear conversion gain.
RF input power	The maximum power level that can be applied to the RF input for the mixer to perform within its specifcation.
LO input power	The recommended power level for the local oscillator signal at the LO input.
IF output power
Maximum LO input VSWR	In order to achieve its required performance the local oscillator source impedance must match the required impedance. This specification gives the maximum VSWR for it to reach its specified performance.
Max output spurious emissions	The maximum level is unwanted spurious signals relative to the wanted one expressed in dB.

These are the main RF mixer parameters that have been included in our list. There are others, but the ones included are the main ones encountered.

Read more about . . . . RF Mixer Data-sheet Specifications & Parameters.

Please note, that the data given is the best estimate we can give within a tabulated summary of this nature. Parameters also vary between manufacturers. Electronics Notes cannot accept any responsibility for errors, inaccuracies, etc, although we do endeavour to ensure the data is as accurate as possible.

Notes and supplementary information

• Availability & sources

The ADE-1H+ is available from a number of stockists and electronic component distributors many of which are given in the table below.

ADE-1H+ Component Distributor, Stock and Pricing

• Further details

The ADE-1H+ is a passive mixer using the standard format. As such it includes RF transformers to ensure the correct phasing, transformation etc. It is the use of transformers that contribute to much of the bandwidth limitations, although other aspects of the performance can be exceptional.