GPRS Operation & States
There are three different operational states in which a GPRS can exist: initialisation / idle, standby and ready.
GPRS General Packet Radio Service Tutorial Includes:
GPRS basics
Network architecture
Mobile / multislot classes
Radio interface
Coding
Channels: physical, logical, control
GPRS protocol stack
Operational states
The operation of a GPRS mobile is characterised by its three operational states: initialisation / idle, standby and ready.
As the GPRS mobile can be always connected in terms of data, the mobile has tree operational states that are defined.
Initialisation / idle
When the mobile is turned on it must register with the network and update the location register. This is very similar to that performed with a GSM mobile, but it is referred to as a location update. It first locates a suitable cell and transmits a radio burst on the RACH using a shortened burst because it does not know what timing advance is required. The data contained within this burst temporarily identifies the mobile, and indicates that the reason for the update is to perform a location update.
When the mobile performs its location update the network also performs an authentication to ensure that it is allowed to access the network. As for GSM it accesses the HLR and VLR as necessary for the location update and the AuC for authentication. It is at registration that the network detects that the mobile has a GPRS capability. The SGSN also maintains a record of the location of the mobile so that data can be sent there is required.
Standby
The mobile then enters a standby mode, periodically updating its position as required. It monitors the MNC of the base station to ensure that it has not changed base stations and also looks for stronger base station control channels.
The mobile will also monitor the PPCH in case of an incoming alert indicating that data is ready to be sent. As for GSM, most base stations set up a schedule for paging alerts based on the last figures of the mobile number. In this way it does not have to monitor all the available alert slots and can instead only monitor a reduced number where it knows alerts can be sent for it. In this way the receiver can be turned off for longer and battery life can be extended.
Ready
In the ready mode the mobile is attached to the system and a virtual connection is made with the SGSN and GGSN. By making this connection the network knows where to route the packets when they are sent and received. In addition to this the mobile is likely to use the PTCCH to ensure that its timing is correctly set so that it is ready for a data transfer should one be needed.
With the mobile attached to the network, it is prepared for a call or data transfer. To transmit data the mobile attempts a Packet Channel Request using the PRACH uplink channel. As this may be busy the mobile monitors the PCCCH which contains a status bit indicating the status of the base station receiver, whether it is busy or idle and capable of receiving data. When the mobile sees this status bit indicates the receiver is idle, it sends its packet channel request message. If accepted the base station will respond by sending an assignment message on the PAGCH on the downlink. This will indicate which channel the mobile is to use for its packet data transfer as well as other details required for the data transfer.
This only sets up the packet data transfers for the uplink. If data needs to be transferred in the downlink direction then a separate assignment is performed for the downlink channel.
When data is transferred this is controlled by the action of the MAC layer. In most instances it will operate in an acknowledge mode whereby the base station acknowledges each block of data. The acknowledgement may be contained within the data packets being sent in the downlink, or the base station may send data packets down purely to acknowledge the data.
When disconnecting the mobile will send a packet temporary block flow message, and this is acknowledged. Once this has taken place the USF assigned to the mobile becomes redundant and can be assigned to another mobile wanting access. With this the mobile effectively becomes disconnected and although still attached to the network no more data transfer takes place unless it is re-initiated. Separate messages are needed to detach the mobile from the network.
As the GPRS mobile set uses packet data and can be in an always connected state, it is encessary to defien the tree operational states.
Wireless & Wired Connectivity Topics:
Mobile Communications basics
2G GSM
3G UMTS
4G LTE
5G
Wi-Fi
Bluetooth
IEEE 802.15.4
DECT cordless phones
Networking fundamentals
What is the Cloud
Ethernet
Serial data
USB
LoRa
VoIP
SDN
NFV
SD-WAN
Return to Wireless & Wired Connectivity